Toyota Venza TPMS Reset Button Location (All Years)

Last Updated on June 27, 2026 by Ryan

The Toyota Venza’s TPMS reset button location depends entirely on which generation you own, and that detail trips up more owners than any other step in this process. The first generation Venza, built from 2009 to 2015, uses a small physical button. The second generation, the Hybrid only model reintroduced in 2021, does not have a confirmed dedicated button at all.

Pressing a button also assumes your sensors are healthy. Many first generation Venzas are now old enough that the sensor batteries are failing, and a reset button cannot fix that on its own.

This guide covers the exact reset steps for both generations, explains why some owners never find a button on their car, and flags a 2025 Toyota recall that can hide a tire pressure warning entirely.

Where Is the TPMS Reset Button on Your Venza

The answer depends on your Venza’s model year. The table below gives the short version for both generations, and the sections after it walk through each one in full detail.

If you drive a 2009 to 2015 Venza, jump to the next section. If you own a 2021 or newer Venza Hybrid, skip ahead to the second generation steps.

TPMS Reset Steps for the 2009 to 2015 Venza

Toyota built the first generation Venza on a direct TPMS system, the same setup used across most Toyota and Lexus models from that era. Direct systems read real tire pressure from a sensor inside each wheel, and they include a small reset button for re-syncing those readings.

Owner reports and trade sources place this button in two different spots depending on trim level. Some 2009 to 2015 Venzas have it tucked below the steering column near the brake pedal. Others have it inside the glove box.

If your Venza’s button matches neither spot, check the sticker inside your glove box or your owner’s manual. The Toyota Camry TPMS reset button location follows the same general pattern, since both cars share the same era of direct TPMS hardware.

Once you find it, the reset sequence is straightforward:

1. Inflate all four tires, and the spare if equipped, to the pressure listed on the driver door jamb sticker.
2. Turn the ignition to ON without starting the engine.
3. Press and hold the reset button until the TPMS light blinks slowly three times.
4. Start the engine and let it run for several minutes so the system records each tire’s pressure.

Toyota’s own support documentation confirms this exact sequence, holding the button until the light blinks three times before letting the engine run to record pressure.

This button only re-syncs sensor IDs already stored in memory. If you just installed new tires or new sensors, pressing it alone will not register them, and a scan tool is required for that step instead.

First generation owners now have their answer. Second generation Venza Hybrid owners need a completely different approach.

TPMS Reset on the 2021 to 2026 Venza Hybrid

Toyota brought the Venza back in 2021 as a Hybrid only crossover built on a different platform, and the TPMS system changed along with it. There is no widely confirmed physical reset button on this generation.

Instead, the system is designed to relearn on its own:

1. Inflate all tires to the pressure listed on the driver door jamb.
2. Drive above roughly 20 mph for 10 to 15 minutes so the sensors can recalibrate.
3. Check the tire pressure readout on the multi information display once you are parked again.

Some sites claim a Reset TPMS option exists inside the infotainment settings menu on this generation. We could not confirm this against an official Toyota source, so treat it as unverified until your owner’s manual or a dealer confirms it for your specific trim.

If the light stays on after driving, the relearn process used on the Toyota RAV4 TPMS reset button location guide is built on a similar Toyota platform and offers a useful second reference point.

Whichever generation you own, a button press or drive cycle only works if the underlying hardware is healthy. That is not always the case.

Why Some Venza Owners Cannot Find a Reset Button

If you have searched under your dash for fifteen minutes and found nothing, you are not imagining it. Several Venza owners report the exact same experience to Toyota dealers and tire shops.

A 2013 Venza owner reported being told directly by a dealer that no reset switch exists on their specific car, and similar reports appear from 2011 and 2021 Venza owners as well.

This usually comes down to trim variation, not a defect. Lower trims built in certain years may have shipped without the secondary switch that higher trims include, and the button’s small size makes it easy to miss even when it is present.

If no button turns up anywhere in your Venza, correcting the tire pressure and driving for several minutes clears the light on most direct TPMS systems, button or no button. Owners replacing failing sensors on a car with no working button sometimes upgrade to a standalone unit instead, and our roundup of the best tire pressure monitoring systems covers reliable current options.

A missing button is one possibility. A light that will not clear at all points to something else entirely.

What a TPMS Light That Stays On Really Means

A solid TPMS light almost always means low tire pressure, and it should clear once every tire is corrected. A light that blinks for about a minute and then stays on points to a system fault instead, not a pressure problem.

TPMS sensor batteries are sealed and cannot be replaced on their own. They typically last five to ten years, and most first generation Venzas are now well past that window.

Replacing a failed sensor typically costs between $246 and $313 per wheel once labor and parts are included, according to RepairPal’s general estimator, though independent tire shops and warehouse clubs often charge less than a dealership for the same job.

Confirming a dead sensor before paying for a replacement takes a TPMS capable scan tool. Our guide to the best OBD2 scanner for Toyota vehicles covers tools that can read individual sensor IDs and pressure data directly.

Sensor failure explains most stuck lights. A separate, newer issue can also make the light appear broken even when the TPMS system itself is fine.

The 2025 Toyota Recall Affecting Venza Tire Pressure Warnings

In September 2025, Toyota issued a safety recall covering roughly 591,000 vehicles in the United States, including 2023 to 2024 Venza models. The recall addresses a software error in the 12.3 inch instrument panel display.

Toyota’s recall notice explains that the display can go blank at startup, which hides the tire pressure warning along with vehicle speed and brake system indicators.

This means a Venza owner could believe a reset fixed their TPMS light when the display itself simply failed to load, not the tire pressure system. Dealers will inspect and update or replace the instrument cluster software at no cost.

Check your Venza’s VIN through Toyota’s own recall lookup tool before assuming a stuck light is strictly a TPMS hardware problem. A blank display can look exactly like a system that never reset at all.

Finding the Right TPMS Fix for Your Venza

The Toyota Venza TPMS reset button location depends on the generation you drive, not on a universal fix. A 2009 to 2015 Venza usually has a small physical button, while a 2021 or newer Hybrid relies on a drive cycle instead.

If pressing the button or completing the drive cycle does not clear the light, aging sensor batteries are the most likely cause on an older Venza. Check the 2025 recall too, since a blank display can look exactly like a stuck warning light.

Start with the correct steps for your generation, confirm your tire pressure is accurate, and move to sensor replacement only after a scan tool rules out a simpler fix.

Frequently Asked Questions About Venza TPMS Reset

Does the 2021 Toyota Venza have a TPMS reset button?

No confirmed dedicated reset button exists on the 2021 or newer Venza Hybrid. Toyota’s updated TPMS on this generation typically self relearns once you drive above about 20 mph for 10 to 15 minutes with correct tire pressure.

How long does a Venza TPMS reset take?

A first generation Venza usually takes a few minutes once the button is held until the light blinks three times. The second generation Hybrid takes longer, since it relies on a 10 to 15 minute drive cycle instead of a button press.

Why is my Venza’s TPMS light blinking instead of staying on solid?

A blinking light, especially one that flashes for about a minute before going solid, signals a system fault rather than low pressure. This usually points to a failed sensor and needs a scan tool to confirm before any parts get replaced.

Can I reset Venza TPMS myself after installing new tires?

The physical reset button only re-syncs sensor IDs already stored in the system. New tires or new sensors need to be registered with a TPMS capable scan tool first, which most tire shops and dealers can do during installation.

Is my Venza affected by the 2025 Toyota instrument panel recall?

Models from the 2023 to 2024 model years are included in Toyota’s September 2025 recall for a display issue that can hide warning lights. Check your VIN through Toyota’s recall lookup tool to confirm your specific vehicle.