2011 Subaru Outback Oil Light Reset: Quick and Easy Guide

Last Updated on September 29, 2023 by Albert Duke

To reset the oil light on a 2011 Subaru Outback, turn the ignition key clockwise until all the function lights appear, just before starting the ignition. Wait until all the lights turn off, and the oil light should be reset.

Credit: www.carsguide.com.au

Locating The Fuse Box

To locate the fuse box for a 2011 Subaru Outback oil light reset, turn the ignition key clockwise until all function lights appear, just before starting the ignition. Instructions for resetting the oil light can be found online, usually involving a sequence of key turns and button pushes.

Step-By-Step Guide On How To Locate The Fuse Box In A 2011 Subaru Outback:

To reset the oil light in your 2011 Subaru Outback, you need to locate the fuse box. Here is a step-by-step guide on how to do it:

• :
• The fuse box in the 2011 Subaru Outback is located under the hood of the car.
• Open the hood of your Outback and prop it up securely.
• Look for a rectangular box with a removable cover on the driver’s side of the engine bay.
• It might be labeled “Fuse Box” or have a diagram indicating its location.
• Removing the Fuse Box Cover:
• Once you have located the fuse box, carefully remove the cover.
• Some fuse box covers have clips that need to be released, while others have screws or tabs.
• Use a screwdriver or your fingers to loosen the clips, screws, or tabs and remove the cover.
• Identifying the Oil Light Fuse:
• Inside the fuse box, you will find a series of fuses and relays.
• Look for the fuse labeled “Oil Light” or something similar.
• Refer to your vehicle’s owner’s manual or the fuse box diagram to identify the specific fuse for the oil light.
• Removing and Replacing the Fuse:
• Once you have identified the correct fuse, carefully pull it out of the fuse box.
• Check the fuse to make sure it is not blown or damaged.
• If the fuse is fine, reinsert it back into the fuse box in the same slot.
• Make sure it is secure and properly seated.
• Closing the Fuse Box:
• After you have replaced the fuse, place the fuse box cover back on.
• Align the cover with the fuse box and secure it using the clips, screws, or tabs.
• Ensure that the cover is snugly in place to protect the fuses and relays.
• Verifying the Reset:
• Close the hood of your Subaru Outback.
• Start the engine and check if the oil light has been successfully reset.
• If the light is still on, repeat the steps above to ensure that the fuse is properly inserted and functioning.

Remember, always consult your vehicle’s owner’s manual for specific instructions and diagrams to locate the fuse box and reset the oil light in your 2011 Subaru Outback.

Turning The Key To Accessory Mode

To reset the oil light on a 2011 Subaru Outback, turn the key to accessory mode, locate the fuse box, remove the fuse, put it back in, and start the car. It’s a simple process that can be found online with step-by-step instructions.

Clear Instructions On How To Turn The Key To Accessory Mode In Order To Reset The Oil Light:

To reset the oil light on your 2011 Subaru Outback, it is important to follow the correct sequence of actions. Here’s a step-by-step guide on how to turn the key to accessory mode and reset the oil light:

• Locate the fuse box: The fuse box in your Subaru Outback is usually located on the driver’s side. Look for a rectangular box with a removable lid.
• Remove the fuse: Find the fuse labeled “ACC” or “Accessory” and carefully remove it from the fuse box. This will prevent the engine from starting while you perform the reset.
• Turn the key to accessory mode: Insert the key into the ignition and turn it clockwise until all the function lights appear on the dashboard. Make sure that the key is turned just before the final turn to start the ignition.
• Wait for the lights to appear: Once you have turned the key to accessory mode, wait until all the function lights on the dashboard are illuminated. This may take a few seconds.
• Put the fuse back in: After all the function lights have appeared, insert the fuse labeled “ACC” or “Accessory” back into the fuse box. Make sure it is securely in place.
• Start the car: Now that the oil light has been reset, you can start the engine of your Subaru Outback. The oil light should no longer be illuminated on the dashboard.

Following these clear instructions will allow you to turn the key to accessory mode and successfully reset the oil light on your 2011 Subaru Outback. Remember to always consult your vehicle’s manual or seek professional help if you have any concerns or difficulties during the process.

Safe driving!

Putting The Fuse Back In

To reset the oil light on a 2011 Subaru Outback, start by turning the ignition key clockwise until all the function lights appear, just before starting the ignition. Wait until all the lights turn off, indicating that the oil light has been reset.

If needed, instructions for resetting can be found online.

Presses), or you can refer to your vehicle’s owner’s manual for guidance. However, if you’re specifically looking for instructions on how to put the fuse back in after turning the key to accessory mode, here are the detailed steps to follow:

Detailed Steps To Follow In Order To Put The Fuse Back In After Turning The Key To Accessory Mode:

• Locate the fuse box in your Subaru Outback. It is usually found under the dashboard on the driver’s side or in the engine compartment. Refer to your vehicle’s owner’s manual for the exact location if needed.
• Once you’ve located the fuse box, open the cover to access the fuses inside. Be careful not to damage any surrounding components while doing so.
• Look for the fuse that corresponds to the oil light or any other related indicator. The fuses are usually labeled, so check the diagram on the fuse box cover or in your owner’s manual to identify the correct one.
• Gently remove the fuse from its socket by pulling it straight out. Take note of the fuse’s position and orientation so that you can put it back correctly later. It’s always a good idea to double-check the owner’s manual for any specific precautions or details related to removing and inserting fuses in your particular model.
• Inspect the fuse to ensure it is not blown or damaged. If the fuse is faulty, replace it with a new one of the same amperage rating. It’s always recommended to carry a spare fuse of each type in your vehicle for emergencies.
• Align the replacement or the original fuse with the empty socket and carefully insert it. Make sure it fits snugly and is fully seated.
• Once the fuse is securely in place, close the fuse box cover.
• Now, turn the key to accessory mode again to test if the oil light or any related indicator has been reset. Check to see if the light has turned off or if any error messages have disappeared from your dashboard.
• If the oil light doesn’t reset, or if you experience any other issues with your vehicle’s indicators, it’s advisable to consult a professional mechanic or refer to Subaru’s official technical support for further assistance.
• Finally, start the car to ensure everything is functioning properly. If the oil light stays off and there are no other warnings, you have successfully put the fuse back in after turning the key to accessory mode.

Remember to always follow the recommended procedures and exercise caution when working with fuses or any other electrical components in your vehicle. If you’re not comfortable performing these tasks yourself, it’s best to seek professional help.

Starting The Car

To reset the oil light on a 2011 Subaru Outback, turn the ignition key clockwise until all the function lights appear. Wait until all the lights come on, then start the car. Alternatively, you can find instructions online for a sequence of key turns and button pushes.

:

To reset the oil light on your 2011 Subaru Outback, follow these steps:

• Turn the ignition key clockwise until all the function lights appear. This is just before the final turn to start the ignition. Wait until all the lights are illuminated.
• Once all the function lights are on, you can proceed with starting the car as you normally would. Turn the key all the way to start the engine.

That’s it! By starting the car after following these steps, you should be able to reset the oil light on your Subaru Outback.

Additional Tips Or Troubleshooting For Cases Where The Oil Light Does Not Reset:

Sometimes the oil light may not reset even after following the initial steps. Here are a few additional tips and troubleshooting steps you can try:

• Check the owner’s manual: Refer to your vehicle’s owner’s manual for specific instructions on how to reset the oil light. The steps may vary depending on the model and year of your Subaru Outback.
• Double-check the sequence: Make sure you are following the correct sequence of key turns and button pushes to reset the oil light. Even a small error in the process can prevent the light from resetting.
• Disconnect the battery: Disconnecting the battery for a few minutes can sometimes help reset the oil light. This essentially resets the car’s electrical system and may clear any errors causing the light to remain on.
• Consult a professional: If you’ve tried the above steps and the oil light still won’t reset, it’s best to consult a professional mechanic or contact your local Subaru dealership for further assistance.

Remember to always exercise caution and follow safety procedures when working with your vehicle’s electrical system. If you’re unsure about any of the steps, it’s recommended to seek professional help to avoid any potential damage or accidents.

Following these additional tips and troubleshooting steps should help you resolve any issues with resetting the oil light on your 2011 Subaru Outback.

Additional Resources And Troubleshooting

To reset the oil light on a 2011 Subaru Outback, you can follow simple instructions found online. This typically involves a sequence of key turns and button pushes. Remember to disconnect the battery if the light doesn’t reset automatically.

F buttons or switches that need to be pressed in a specific order). In addition to online resources, there are common troubleshooting issues that you may encounter when it comes to the oil light reset process. Here are some additional resources and troubleshooting tips to help you with the 2011 Subaru Outback oil light reset:

Suggesting Online Resources To Find Specific Instructions For Individual Car Models:

• Google Search: Use specific keywords like “2011 Subaru Outback oil light reset” to find relevant websites and forums that provide step-by-step instructions for your specific car model.
• YouTube: Search for video tutorials on resetting the oil light for the 2011 Subaru Outback. Many automotive channels provide visual demonstrations that can be helpful in understanding the process.
• Subaru Owner’s Manual: Refer to the official owner’s manual for your 2011 Subaru Outback. It should have detailed instructions on how to reset the oil light.

Common Troubleshooting Issues And Solutions When It Comes To The Oil Light Reset Process:

• Ignition Key Turn: Make sure to turn the ignition key clockwise until all the function lights appear right before starting the ignition. Wait until all the lights are on before proceeding with the reset process.
• Fuse Removal: Locate the fuse box in your Subaru Outback and remove the appropriate fuse related to the oil light. Refer to your owner’s manual for the exact location.
• Accessory Mode: Turn the key to the accessory mode position to enable the reset procedure. This will allow you to interact with the vehicle’s systems without starting the engine.
• Fuse Replacement: After a few seconds, put the fuse back in its original position. Make sure it is securely in place to ensure proper functioning of the oil light.
• Start the Car: Start the engine and check if the oil light has been successfully reset. If the light is still on, repeat the process or consult a professional mechanic for further assistance.

Remember, if you’re ever unsure or uncomfortable with the oil light reset process, it’s always a good idea to consult a qualified mechanic or refer to the official Subaru service center. They can provide you with expert advice and assistance to ensure everything is done correctly and safely.

Frequently Asked Questions Of 2011 Subaru Outback Oil Light Reset

How Do You Reset The Oil Light On A 2011 Subaru Outback?

To reset the oil light on a 2011 Subaru Outback, follow these steps: 1. Turn the ignition key clockwise until all the function lights appear before starting the engine. 2. Wait until all the lights turn off, including the oil light.

3. If the light persists, you can try disconnecting the battery to reset it. 4. Alternatively, you can search online for specific instructions on how to reset the oil light for your particular model.

How Do You Reset The Oil Light On A Subaru Outback?

To reset the oil light on a Subaru Outback, turn the ignition key clockwise until all function lights appear. Wait until all lights are on, then turn the key to start the ignition.

How Do You Reset The Oil Life On A 2011?

To reset the oil life on a 2011 Subaru Outback, turn the ignition key clockwise until all the function lights appear, just before starting the ignition. Wait until all lights turn off and the oil life should be reset. You can also find instructions online for specific sequence of key turns and button pushes.

How Do You Reset The Oil Light On A 2011 Subaru Legacy?

To reset the oil light on a 2011 Subaru Legacy, follow these steps: 1. Turn the ignition key clockwise until all the function lights appear. 2. Wait until all the lights turn off, including the oil light. 3. Repeat this process a few times to ensure that the oil light is reset.

4. If the oil light persists, you can try disconnecting the battery to reset the light. Please note that if the oil light continues to come on after resetting, it is advisable to have your vehicle checked by a professional.

Conclusion

Resetting the oil light on a 2011 Subaru Outback is a simple procedure that can be done at home. By following the instructions provided by online resources such as videos, forums, and guides, you can easily turn off the low oil light after an oil change.

The process usually involves a sequence of key turns and button pushes, which can vary slightly depending on the specific model. It is important to make sure that the ignition is in the correct position before starting the reset procedure.

If you encounter any issues or are unsure about the steps, it is always a good idea to consult with a professional or contact the manufacturer for guidance. By resetting the oil light, you can ensure that your Subaru Outback is running smoothly and efficiently, giving you peace of mind on the road.